A: An OSSM is compact sex machine that can be customised to suit you. Based around a NEMA23 pattern for electric motors it can be driven by stepper or best of all servo motors it uses a combination of 3D printed and off the shelf parts.
A: The OSSM is open you are not tied to a specific company and it does a lot more than equivalently priced machines. Best of all you can fully control the stroke speed and most importantly depth. You can make patterns or even your own control software. Maybe you want to add a stroker rather than a dildo, you can modifiy it to do that. Not enough power? You can use a bigger motor up to a certain point.
A: Head over to the README - the BOM is maintained there.
A: While you can theoretically use any Nema23 mount motor. There are motors that work and some that work better. Stepper motors are cheaper and noiser so the community recommends closed loop servo motors. These are more efficient and more importantly easier to program.
A: That depends on a couple of factors.
We don’t have a lot of recorded data [Please help us with this!] however the general suggestions are;
A build with a servo motor will have a flat torque curve across the speed range. That’s to say - it will push just as hard at the slow speeds as well as the fast. With a stepper, the most force will be at the slower speeds and the top speed of a stepper is much less than the servo we’ve chosen to work with.
A: Butts have big powerful muscles! It’s common for people to bear down, or clench when things are feeling really good. Also it can be pretty fun shoving big objects in there! It can take a big motor to handle a big toy in a poweful butt.
A: The minimum bed size is 105mm x 105mm for the largest single piece. Approximately 125mm of height is required for the shorter vac-u-lock compatible adapter, the plate is significantly shorter.
A: All of our testing has been with simple PLA, however if you do print it in an interesting material make sure to share it to the discord!
A: 30% has been found to work just fine with PLA for non flexible parts
A: Recommend at least 3mm for non flexible parts.
A: There are mounting solutions that use clamps for the OSSM these need some flexiblity. For these parts thinner walls 2mm, lower infill percentages and a gyroid pattern.
A: Aside from the motor this is second decision. There is a vacc-u-lock compatible mount the double double and a plate mount for suction cup toys that has some points to tie a dildo down The OSSM Platten
A: Well there are a few designs available. THere are standard pipe mounts for US/Canadian along with 80/20 rails that can be used like a construction set. There are even manfrotto boom compatible adaptors. It is really limited by you imagination.
A: It depends on how you are going to use it. Basic OSSM control is via the wired remote and a more advanced remote is available from community members (M5 Remote). If you want something specific you can create your own that is the great thing about open source hardware.
A: As of August 2023 you cannot control an OSSM over the internet. In the past R&D offered a web page that allowed very basic control with speed and depth settings over wifi.
A: As of August 2023 there is a highly experimental X-toy firmware forked from an earlier version that requires endstops. This code has significant issue and is not considered to be safe for use on humans. There are frequent pauses, it loses track of where it is and has a tendency to randomly extend to maximum depth. Development of an X-Toys firmware is happening but it is complicated.
A: Things are a lot more complicated once you dig down into them.
A: No you don’t but it does make building an OSSM a lot easier and stops you having to solder anything.
A: That is linked to the size of motor. The higher the wattage of motor the larger the powersupply you need. For safety use a desktop power supply that is ideally double insulated. Power supplies from Mouser/Digikey/Conrad/RS etc are all typically more expensive than “no brand supplies” you get from AliExpress/eBay/Amazon. Experience has been mixed with unbranded supplies with occasional quality and longer term stability issues.
A: It is really up to you but a 350mm rail will give approximately 195mm of depth.
A: It is a M24x3 (this is the size on the machine, do a test print for your new End Effector, you may have to upsize by 3-5%)